Deconstructing a Mobile Home (Part Three)

We were moving at a good clip until we got to the floor. Where the floor isn’t soft from the trailer leaking, it’s difficult to pull apart. The press wood is incredibly heavy and well fastened to the joists, which are 2x4. We tried going at the floor with hand saws, crow bars, hammers, and the like, but I ended up buying a reciprocating saw from Harbor Freight. That's working okay. We're taking it apart in about 1.5 by 5 ft. pieces. It's slow, but coming along. I found a video on Youtube in which young men went at the floor of a mobile home with an ax, but that's not for me. They also cut the steel frame with an angle grinder. Since that's the only info I've seen online regarding actual disassembly of a mobile home, it's probably what I'll try. I'm up for any suggestions that don't involve a welding torch.



Comments

  1. ChesMarch 12, 2011 at 10:35 AM

    We were just at El Dorado Hot Springs in Tonapah, Az. (el-dorado.com.) and they have taken apart several old mobile homes so they can reuse the lumber and siding, having built a shed out of the scrap materials. While we were there we used the 2x from the walls and plywood from the floor to make forms for a new stone and concrete hot tub. I thought about your posting on this subject while we were working. I will be posting on this in the next month or so, so stay tuned to altbuildblog.blogspot.com. There are plenty of old mobile homes out there. It would be nice to see more of them recycled.

    ReplyDelete
  2. park homeFebruary 26, 2013 at 6:39 AM

    Why you always busy in deconstruction? Hey, get some life and build it again what you have already destroyed.

    ReplyDelete

Post a Comment

Popular posts from this blog

Drip Irrigation Experiment 2

Image
I placed another four inch block under the barrel (I think the higher it is, the better) and changed the middle four way connector to a tee, eliminating the middle emitter pipe. Then I graded the bed a little toward the barrel and water flow is much better. I think the 1/8” holes may be too large. I’ll be making another drip irrigator for a smaller bed, and I’ll drill 1 /16” holes instead. Also on this barrel, the mosquito screen top is in place, held on with a band of hanging wire. Since getting that screen to stay in place was a bit of a pain, I placed a 2” PVC fitting with cap near the top of the barrel as a filler. We’re excited and can’t wait to plant.
Read more

Drip Irrigation Experiment 3

Image
The second drip irrigation barrel was easier and less expensive to make. I drilled a 7/8” hole near the bottom and forced an old ¾” hose bib in. It took a lot of force to start turning that hose bib, but once it was in, no leaks, and no need for a washer or even a nut or fitting to hold it in place. The same went for the 2” PVC fitting used as a fill spout. Cutting the hole just slightly too small made for a tight fit and no fitting on the inside to hold it in place. This bed is not as wide as the other, so I used two emitter pipes rather than four. I drilled 1/16” holes approximately 12” apart. It takes about six hours to empty the 50 gallon barrel, which means, I hope, my irrigator will water our garden plants for six long hot hours each day this summer. I used a product called “Liquid Tape” to seal the 1/8 inch holes on my first effort, and re-drilled on the other side of the pipe with the 1/16” bit.
Read more

Improvised Shelves for our Frigidaire Refrigerator

Image
Well, this is not necessarily recommended. Ask me in six weeks, or six months, how it's going and maybe I'll recommend it then. These machines--these Frigidaire Energy Star refrigerators (like the one we purchased at Lowes only four short years ago) are frail. Seriously. All the cheesy, half-ass components that make this feeble milksop of an appliance come to life supposedly work together to make it more energy efficient. Cheap, frail plastic and glass shelves included. Of course, the energy efficient aspect of these newfangled appliances are supposed to save us money. That's the sales pitch, anyway. We replace our shabby old energy hungry appliances with new ones (appliance purchases usually indiiate an emergency, so we might well be using our credit card to make the purchase), and we're rewarded not only by a cleaner environment, but with a slightly fatter wallet. Only so far, this particular appliance is begging to be replaced after only four years. That's not le
Read more