Low Rent Renaissance

] The papercrete "gazebo" structure that I made years ago was showing some deterioration, especially the areas where the papercrete was most exposed to weather. I used type S mortar to cover the weathered papercrete, and reworked most of the faces using my "sculpture" mortar mix. The papercrete "trees" on the back side of the structure had held up well, so I left them except to stain them with exterior wood stain, to bring them out a bit and help preserve them. 

I finally had the opportunity to work on the gazebo. Inclement weather, early sundowns, and other projects always seem to get the way of adding more papercrete to the structure. The other projects include renovating a 40 year old mobile home (I'm replacing the windows first (two down, ten to go), building a papercrete "sprayer" for use with an air compressor, and, of course, working on polymer sculptures. I'm hoping to post photographs of the mobile home (and new sculptures) as we progress. The trailer has been on our property awhile, and we were going to give it to the in laws to use for storage. But the county will not give us a permit to move a mobile home build prior to 1985 unless it's going to the land fill. Nor will they give a contractor a permit to rewire the thing. We felt it was just too valuable a space to pay someone to haul it to the dump, so we're taking it "off grid" and turning it into a studio. I'm hoping to cover the entire be...

I've been adding more papercrete to the fence/hardware cloth/chickenwire armature, using small, hand-mixed batches of the sculptue mix, which is cellulose insulation, Portland cement, and joint compound, with no sand. Once this dries I think the armature will be more substantial, and additional layers may be of the "construction" mix using the tow mixer, which will probably go faster. The poles at the entrance will be totems. Since they are upright (and I'll be working "against gravity") I'm going to try fastening the faces to the crete-covered poles with masonry glue and wood screws, and papercreting around them.

The wire armature for the gazebo is almost complete. I couldn't wait, and started daubing papercrete on. I'm interested to see if the armature will be sturdy enough. My pre-soaked cellulose papercrete formula wasn't working out. There was just too much slump. The crete would not stick to the upright armature. So, instead of my usual sculpture mix, I mixed three 2-pound coffee cans of dry cellulose insulation and one can of Portland cement, then added water until it was a damp, thick paste. Then, instead of the powdered joint compound I've been sold on, I added (a big gob) of premixed joint compound. The result, when well mixed by (rubber-gloved) hand, was truly clay-like and stuck well to the chicken wire and hardware cloth. Hope to work more on it tomorrow.

It doesn't look like much yet. You can barely see the fence wire form, which is almost complete, in the bottom photograph. All but the center post, which is just a 10 ft. 4x4, are made the same way as the armature for the totem pole shown in an earlier post. I had doubts about making the armature this way, thinking I had to wrap a whole 4x4 post with hardware cloth to get a sturdy armature, but the finished totem pole seems incredibly strong, and I was inspired to make the posts for this project the same way. Especially since the "key stone" of this structure is the center post anyway. On the papercrete post, the hardware cloth is tacked to a three foot piece of 4x4 with fence nails. The post extends into the hardware cloth tube approximately one foot, so there are two feet of bare wood at the bottom. The posts are then set so that the hardware cloth is about an inch above ground level. I can go directly over the hardware cloth with papercrete. For the center support, I b...

So the neighbor was setting up her patio umbrella to sell at her yard sale and somehow broke the shaft. And I kept thinking that, coated with latex cement (the same stuff with which I made the fly screen skirting for our mobile home as described in an earlier post) it would make a great dome-like roof for a small gazebo. And so I gave her $5 for her broken umbrella and added a papercrete gazebo to my ever-growing "to do" list. Naturally, I didn't photograph the umbrella before I coated it, but here it is after a couple of coats of latex cement.