Low Rent Mortar Sprayer #2

My very simple and inexpensive home made mortar sprayer has served me well until lately, when it started clogging every few minutes. I thinned my mortar mix a little and hosed my sprayer out, but every few minutes I'd have to stop. My theory is that sand has scarred the soft PVC plastic or copper nozzle enough to catch a little mortar and make it accumulate there. Or maybe it was the latex cement I sprayed that makes the mortar stick. Regardless, I had to replace my sprayer, and wanted to do it in a way I could duplicate easily.


As before, I started with a 1-1/4" male threaded cap and a 1-1/2 to 1-1/4 female threaded bushing, I also used a gnarled adapter for my air gun, and a small copper nozzle.



The nozzle and spray hole in the cap need to line up, which can be a little tricky on a rounded piece. I drilled just above the ridge at the bottom of the cap, using the small bit (9/32) first, and drilled all the way through the fitting so I had a hole front and back. Then I enlarged one hole, the spray hole, with a bigger bit (7/16).




I used a Dremel tool to cut the tip off the nozzle, which was too long and didn't allow for enough space between the nozzle tip and the spray hole. I thought I might have cut it too short, but the sprayer works fine.  I sanded the rough nozzle tip and buffed it smooth with the Dremel.



I used the Dremel to cut the ridge off just below the nozzle hole so the gnarled adapter, air gun, etc, will fit and turn freely to tighten. Then I sanded and buffed the area clean

The PVC fitting is too thick. the threads of the nozzle barely go through to the other side, and the gnarled adapter can't grab them. I sanded the inside of the fitting with the Dremel tool a little just around the nozzle hole to thin the plastic a bit, and buffed it smooth.

Here is the fitting with the nozzle and gnarled adapter attached.

The bushing screws onto the cap tight against the gnarled adapter to help hold it in place. The hopper is a gallon jug with the bottom cut out.  The cap threads of the jug don't exactly match those of the bushing.  I've used a large Clorox bottle successfully. A little electrical tape around the cap threads helps hold it tight. I've not had any trouble with the hopper coming loose. Inevitably mortar seeps in and holds everything tight.



Comments

  1. UnknownAugust 26, 2015 at 10:40 PM

    Awesome! Thank you for sharing this. Exactly what I needed!

    ReplyDelete

Post a Comment

Popular posts from this blog

Drip Irrigation Experiment 2

Image
I placed another four inch block under the barrel (I think the higher it is, the better) and changed the middle four way connector to a tee, eliminating the middle emitter pipe. Then I graded the bed a little toward the barrel and water flow is much better. I think the 1/8” holes may be too large. I’ll be making another drip irrigator for a smaller bed, and I’ll drill 1 /16” holes instead. Also on this barrel, the mosquito screen top is in place, held on with a band of hanging wire. Since getting that screen to stay in place was a bit of a pain, I placed a 2” PVC fitting with cap near the top of the barrel as a filler. We’re excited and can’t wait to plant.
Read more

Drip Irrigation Experiment 3

Image
The second drip irrigation barrel was easier and less expensive to make. I drilled a 7/8” hole near the bottom and forced an old ¾” hose bib in. It took a lot of force to start turning that hose bib, but once it was in, no leaks, and no need for a washer or even a nut or fitting to hold it in place. The same went for the 2” PVC fitting used as a fill spout. Cutting the hole just slightly too small made for a tight fit and no fitting on the inside to hold it in place. This bed is not as wide as the other, so I used two emitter pipes rather than four. I drilled 1/16” holes approximately 12” apart. It takes about six hours to empty the 50 gallon barrel, which means, I hope, my irrigator will water our garden plants for six long hot hours each day this summer. I used a product called “Liquid Tape” to seal the 1/8 inch holes on my first effort, and re-drilled on the other side of the pipe with the 1/16” bit.
Read more

Improvised Shelves for our Frigidaire Refrigerator

Image
Well, this is not necessarily recommended. Ask me in six weeks, or six months, how it's going and maybe I'll recommend it then. These machines--these Frigidaire Energy Star refrigerators (like the one we purchased at Lowes only four short years ago) are frail. Seriously. All the cheesy, half-ass components that make this feeble milksop of an appliance come to life supposedly work together to make it more energy efficient. Cheap, frail plastic and glass shelves included. Of course, the energy efficient aspect of these newfangled appliances are supposed to save us money. That's the sales pitch, anyway. We replace our shabby old energy hungry appliances with new ones (appliance purchases usually indiiate an emergency, so we might well be using our credit card to make the purchase), and we're rewarded not only by a cleaner environment, but with a slightly fatter wallet. Only so far, this particular appliance is begging to be replaced after only four years. That's not le
Read more